Buying Guide
Selecting the best industrial electrical capacitors for motors is primarily an identification task. A capacitor that looks similar may still be wrong if its capacitance, voltage, duty, terminal arrangement, or physical envelope differs from the original. Use the existing capacitor label, motor documentation, and equipment wiring diagram together. Disconnect power and follow appropriate electrical safety procedures; capacitor terminals can retain hazardous charge after equipment is switched off.
Match capacitance first
Capacitance is expressed in microfarads, shown as uF or MFD in the listings. The selected products cover single values such as 7.5 uF, 30 uF, and 45 uF; dual-run values such as 35+5 uF, 40+5 MFD, 45+5 uF, and 50+5 uF; and high motor-start ranges such as 233–280 uF and 630–750 uF. The correct number is not interchangeable merely because the case fits.
A dual-run capacitor has two capacitance values in one housing. For example, the BOJACK 45+5 uF model documents separate Herm and Fan terminals plus a Common terminal. That arrangement is appropriate only when the equipment calls for those two values and that wiring configuration. A single-value run capacitor, such as the TEMCo Industrial 30 uF, should not be used in place of a dual-run unit without an equipment-specific design basis.
Start capacitors are a separate design category in this comparison. The BlueStars 233–280 uF, TEMCo Industrial 630–750 uF, and JOCOSA 400–480 uF products are intended for motor-start applications described in their listings. Their higher capacitance ranges do not make them suitable substitutes for continuous run capacitors.
Verify voltage and frequency
Voltage must meet the motor’s requirement. The run-capacitor selections include 370/440VAC or 370/450V designs, while the CD60 start capacitors are listed at 220–250VAC or 250VAC. Do not assume that a higher-looking number is automatically a safe replacement; compare the original marking and manufacturer requirements.
The listings identify 50/60Hz operation for several products, including the Titan TRCFD405, TEMCo Industrial 30 uF, BlueStars 233–280 uF, TEMCo Industrial 630–750 uF, and JOCOSA 400–480 uF. Frequency compatibility remains part of the electrical match, particularly in equipment with a defined operating standard.
Choose run or start duty
Run capacitors remain part of the motor’s operating circuit, while start capacitors provide starting assistance in the applications described by the listings. The product title and specifications should agree with the required duty. CBB65 products in this selection are described as run, dual-run, or run-start units for HVAC, compressor, fan, and motor applications. CD60 products are identified as motor-start capacitors.
The Titan TRCFD405 is a dual-rated 40+5 MFD model with a heat-tolerant metalized polypropylene film. The Globe 7.5 uF product is a fixed single-element oval CBB65 design. These are different formats with different matching considerations. Use the same design type as the original unless the equipment documentation explicitly permits an alternative.
Consider safety evidence and construction
Safety information varies by listing. Titan states compliance with EIA-456A, IEC 60252-1:2001, and UL 810, along with UL and CUL references. TEMCo Industrial 30 uF lists UL E335070 and 10,000 AFC protection. Globe lists a UL-approved pressure-sensitive interrupter and self-healing metalized polypropylene film. Several BOJACK models state a 10,000 AFC safety rating or anti-explosion pressure switch.
These statements are useful specification evidence, but they are not a substitute for checking the exact product marking or local installation requirements. Construction details also differ. Products mention aluminum or metal cases, polypropylene film, oil-filled construction, phenolic resin cases, and PCB-free designs. A stated material can help with comparison, but it does not establish performance beyond the supplied listing.
Check temperature and enclosure space
Temperature ratings are especially relevant around compressors, condenser compartments, and other warm motor equipment. The TEMCo Industrial 30 uF lists the broadest range in this group at -40°C to +85°C. Titan and several BOJACK models list -40°C to +70°C, while the CD60 options generally list ranges ending at +65°C.
Physical dimensions are equally important. The BOJACK 35+5 uF lists approximately a 2-inch diameter and 4.14-inch height; the BOJACK 45 uF lists approximately 1.97 inches by 4.33 inches. The TEMCo Industrial 30 uF lists a 1.76-inch diameter and 3.84-inch height. High-capacitance CD60 units are also comparatively substantial. Measure the available diameter, height, mounting clearance, and terminal direction before ordering.
Compare terminals and replacement practicality
Terminal configuration can determine whether a capacitor is a direct replacement. The BOJACK dual-run products list three top terminals labeled Herm, Fan, and Common. TEMCo Industrial 30 uF and TEMCo Industrial 630–750 uF list 1/4-inch quick-disconnect terminals.
Take a photograph of the original wiring only after power is safely isolated, and compare terminal labels rather than relying solely on wire color. Confirm that the new case can be secured and that terminals will not contact the enclosure.
Use tolerance as a matching detail
Tolerance describes how closely the actual capacitance may fall to the stated value. The JOCOSA model lists ±5%, while the BOJACK run capacitors list ±6%. BlueStars lists ±20% for its 233–280 uF start capacitor. These figures should be read alongside the motor’s permitted specification, not treated as a ranking of universal quality.
Final Recommendation
Titan TRCFD405 40+5 MFD Dual-Rated Capacitor ranks first overall in this specification-based comparison under the published weighted criteria.
Titan TRCFD405 is the highest-scoring returned product and the first overall specification-based choice for a documented 40+5 MFD dual-run requirement. It has unusually complete standards, temperature, voltage, frequency, and construction information. For a 30 uF single run replacement, TEMCo Industrial 30 uF is the most practical alternative because its dimensions, terminals, temperature range, protection, and casing are clearly listed.
Among the top industrial electrical capacitors for motors, the BOJACK 45+5 uF, BOJACK 50+5 uF, and BOJACK 35+5 uF models are useful when the dual-run values match the equipment label. The BOJACK 45 uF and Globe 7.5 uF cover single-value CBB65 applications. For starting duty, choose by the required range: BlueStars 233–280 uF, JOCOSA 400–480 uF, or TEMCo Industrial 630–750 uF. The best industrial electrical capacitors for motors are therefore the ones whose duty, values, voltage, dimensions, and terminals match the motor—not simply the one with the largest capacitance.
Frequently Asked Questions
Match capacitance, voltage, frequency, duty type, terminal arrangement, case shape, and dimensions. For a dual-run unit, match both capacitance values and identify the Common, Fan, and Herm connections where those labels are used. A product such as the BOJACK 45+5 uF documents these details, but the equipment label remains the controlling reference.
Are run capacitors and start capacitors interchangeable?
No. Run capacitors and start capacitors serve different circuit duties. The TEMCo Industrial 30 uF and Titan TRCFD405 are run-capacitor examples, while the JOCOSA 400–480 uF and TEMCo Industrial 630–750 uF are listed as CD60 motor-start products. Select the design specified for the motor.
Is 440V interchangeable with 370V?
Some selected capacitors are specifically dual-rated 370/440V, but that does not mean every capacitor marked 370V can be replaced without checking the equipment requirements. Compare the original voltage marking, capacitance, duty, and manufacturer instructions. The BOJACK 45 uF lists 370/450V, which is a distinct stated rating and should be evaluated as such.
Do capacitor dimensions matter if the electrical values match?
Yes. The case must fit the mounting location, and the terminals must remain accessible without touching grounded metal. The TEMCo Industrial 30 uF and JOCOSA 400–480 uF provide useful dimensional information, while the larger TEMCo Industrial 630–750 uF may need more enclosure space. Confirm measurements before installation.
When is a dual-run capacitor the right choice?
A dual-run capacitor is appropriate when one housing supplies two specified capacitance values for separate motor circuits, commonly compressor and fan circuits in HVAC equipment. The BOJACK 35+5 uF, 45+5 uF, and 50+5 uF listings document this design. Match both values and the terminal labels to the original system.